red lion C48C, Instruction Manual

Page: 46 / 56

-40-
8. OUTPUTS : (Output type and quantity, model dependent)
Solid-State :
NPN Open Collector : I
SNK
= 100 mA max. @ V
OL
= 1.1 VDC max.;
V
OH
= 30 VDC max.
PNP Open Collector : I
SRC
= 100 mA max.(See note);
V
OH
= 12 VDC ±15% (using internal supply); V
OH
= 13 to 30 VDC
(using external supply).
Note: The internal supply of the C48C can provide a total of 100 mA for
the combination of sensor current and PNP output sourcing current.
The supply voltage is +12 VDC (±15%), which will be the PNP output
voltage level when using only the internal supply.
If additional PNP output sourcing current or a higher output voltage
level is desired, an external DC supply may be connected between the
“DC Out/In” and “Comm.” terminals. This supply will determine the
PNP output voltage level, and must be in the range of +13 to +30 VDC.
An external supply can provide the additional output sourcing current
required in applications where two or more outputs are “ON”
simultaneously. However, the maximum rating of 100 mA per individual
output must not be exceeded, regardless of external supply capacity.
Relay : Form A contact, Rating = 5 A @ 250 VAC, 30 VDC (resistive load),
1/10 HP @ 120 VAC (inductive load)
Relay Life Expectancy
: 100,000 cycles min. at max. load rating
Programmable Timed Output : User selectable output time resolution.
0.01 Second Resolution
: 0.01 to 99.99 sec, ± 0.01% +20 msec max.
(Prescalers less than 2)
0.1 Second Resolution
: 0.1 to 999.9 sec, ±100 msec
(Prescalers less than 2)
Note: For Prescaler values above 2, the timed delay output is affected by
the count speed (rate).
9.
RS485 SERIAL COMMUNICATIONS (Optional)
: Up to 32 units can be
connected.
Baud Rate
: Programmable from 1200 to 9600 baud
Address : Programmable from 0 to 99
Data Format
: 10 Bit Frame, 1 start bit, 7 or 8 data bits, 1 or No Parity bit,
and 1 stop bit
Parity
: Programmable for Odd (7 data bits), Even (7 data bits), or None (8
data bits)
10. CERTIFICATIONS AND COMPLIANCES :
CE Approved
EN 61326-1 Immunity to Industrial Locations
Emission CISPR 11 Class A
Safety requirements for electrical equipment for measurement, control, and
laboratory use:
EN 61010-1: General Requirements
EN 61010-2-030: Particular Requirements for Testing and Measuring
Circuits
RoHS Compliant
UL Recognized Component: File #E137808
Type 4X Indoor Enclosure rating (Face only)
IP65 Enclosure rating (Face only)
Refer to EMC Installation Guidelines section of the manual for additional
information.
11. ELECTRICAL CONNECTIONS : Wire clamping screw terminals.
12. CONSTRUCTION : Black plastic case with collar style panel latch. The
panel latch can be installed for horizontal or vertical stacking. Black plastic
textured bezel with clear display viewing window. Unit assembly with circuit
boards can be removed from the case without removing the case from the
panel or disconnecting the wiring. This unit is rated for Type 4X/IP65 indoor
use. Installation Category II, Pollution Degree 2.
13. ENVIRONMENTAL CONDITIONS :
Operating Temperature : 0°C to 50°C
Storage Temperature
: -40°C to 70°C
Vibration to IEC 68-2-6: Operational 5 to 150 Hz, 2 g.
Shock to IEC 68-2-27: Operational 30 g (10 g relay).
Operating and Storage Humidity : 85% max. relative humidity (non-
condensing) from 0°C to 50°C.
Altitude : Up to 2000 meters
14. WEIGHT : 6.0 oz (170 g)