background image

Safety and Installation Instructions 

When using your 

Pr

o

 Burner

, please read and follow these basic precautions:

Power Burner INSTALLATION 

This Outdoor-cooking appliance (Power Burner) must be installed in accordance 
with all local and state codes INSPECTED by your local CITY & Fire department. 
If installation is planned in an area with no local codes, the gas 

burner

 must be

 

installed in accord with the National Fuel Gas Code ANSI Z223.1 and storage 
and handling of liquefied petroleum gases, ANSI/NFPA 58 or CSA B149.1 natural 
gas and propane installation code. ALWAYS USE PROFESSIONAL BUILDERS 
& INSTALLERS.  For Safety 

– have inspected by your local city, Gas Company 

and Fire Department before use.  This is NOT an indoor appliance 

– for outdoor 

use only.

 Do not install into a combustible cabinet without an insulating liner - 

LJRSB3

CALIFORNIA 

PROPOSITION 65

 WARNING

 

The burning of gas cooking fuel generates some by-products, which are on the list 
of substances, which are known by the State of California to cause cancer or 
reproductive harm. California law requires businesses to warn customers of 
potential exposure to such substances. To minimize exposure to these 
substances, always operate the unit according to the use and care manual, 
ensuring you provide good ventilation when cooking. 

NOTE: 

DO NOT USE THIS APPLIANCE UNDER OVERHEAD CONBUSTABLE SURFACES

 

Summary of Contents for PRO RSB3A

















Reviews: