Raytec VARIO2 IP 16 Series Full Installation And Setup Manual Download

Page: 39 / 64

1. Local

The illuminator will respond ONLY to photocell and telemetry events. The user may

also take direct Manual Override control through the Home Page interface. This is the

default setting.

2. VMS

The illuminator will respond ONLY to third party VMS systems and any applications

that use the Raytec API. The illuminator will NOT respond to photocell and telemetry

events. The user CANNOT take direct manual override control through the web

interface.

3. VMS + Local

The illuminator will respond to third party VMS systems and any applications that use

the Raytec API and the illuminator will ALSO respond to photocell and telemetry

events. The user may ALSO take direct Manual Override control through the home

page of the illuminators web interface.

IMPORTANT:

For detailed instructions on

“

VMS

”

and

“

VMS + Local

”

modes please refer to the Raytec

API Document

4. HTTP

The illuminator will respond ONLY to any device / application generating valid HTTP

commands and any applications that use the Raytec HTTP API. The illuminator will

NOT respond to photocell and telemetry events. The user CANNOT take direct

Manual Override control through the web interface.

5. HTTP + Local.

The illuminator will respond to any device / application generating valid HTTP

commands and any applications that use the Raytec HTTP API and the illuminator will

ALSO respond directly to photocell and telemetry events. The user may ALSO take

Summary of Contents for VARIO2 IP 16 Series

































































Search results

Summary of Contents for VARIO2 IP 16 Series

Reviews:

Related manuals for VARIO2 IP 16 Series

Brands by name

Popular brands

Raytec VARIO2 IP 16 Series, Full Installation And Setup Manual

Search results

Summary of Contents for VARIO2 IP 16 Series

Reviews:

Related manuals for VARIO2 IP 16 Series

Brands by name

Popular brands