manualshive.com logo in svg

Raymar 3460, User Manual, Page: 72 / 171

Share
Download
Raymar 3460 User Manual Download Page 72

3460 Fast’R

4-4

4.

In the Fast’RVu main window, select 

• ENCLOSURE LOCATION to operate on a 3460 Fast’R in an 

AccessWay enclosure. 

• MODEM ADDRESS to operate on a stand-alone modem 

5.

In the Fast’RVu main window, select a language.

6.

In the Fast’RVu main window, select an option:

• CONFIGURE, to view and set modem parameters

• STATUS, to view current operating information

• COMMANDS, to dial, get/set, copy, and so on

• TESTS, to execute loopbacks and BER tests

An option window displays.

7.

Optionally: to configure another modem (that isn’t already cabled to 
the computer): disconnect a communications cable from a modem or 
enclosure, and connect it to another one. Repeat this procedure, 
starting with Step 3, to communicate with the modem.
You can communicate with modems that are connected to the 
computer in the following ways:

• A computer cabled to a stand-alone modem’s NC connector

• A computer cabled to AccessWay’s NC connectors. The 

AccessWay may also be cabled to up to three other AccessWays

Specifying a Modem On Which to Operate Fast’RVu

 

Step

Action

Summary of Contents for 3460












































































































































































Reviews:

No comments