manualshive.com logo in svg

Raymar 3460, User Manual, Page: 142 / 171

Share
Download
Raymar 3460 User Manual Download Page 142

3460 Fast’R

C-6

The enclosure has up to 32 female DB25 connectors for connection to a 
computer (DTE), which support a subset of the ITU-T V.24 and EIA/
TIA-232E specifications.

Telephone Connectors, Modems That Support Two- or Four-
Wire Leased or Dial Connection s

LINE A Connectors

Interface

: RJ-11

Connection Type

: Two- or Four-Wire Leased Line or Dial Line

Pin Function

2

Four-Wire Rx Tip

3

Dial-Line Ring/Two-Wire Ring/Four-Wire Tx Ring

4

Dial-Line Tip/Two-Wire Tip/Four-Wire Tx Tip

5

Four-Wire Rx Ring

LINE B Connectors

Interface

: RJ-11

Connection Type

: Two-Wire Leased or Dial Line

Pin Function

3

Two-wire Leased Line/Dial-Line Ring

4

Two-wire Leased Line/Dial-Line Tip

Computer Interface Pin-outs

 

V.24 Signal Number

Pin

Circuit

Function

103

2

BA/103

TXD

104

3

BB/104

RXD

105

4

CA/105

RTS

106

5

CB/106

CTS

107

6

CC/107

DSR

102

7

AB/102

Signal Ground

109

8

CF/109

DCD

114

15

DB/114

TXCLK

115

17

DD/115

RXCLK

Pins not listed here are not used.

Summary of Contents for 3460












































































































































































Reviews:

No comments