Raymar 3460 User Manual Download Page 65

Page: 65 / 171

3460 Fast’R

3-20

NP Parameter Options

Option

Description

*NP0

A local modem, connected through its network control-in (NC IN)
port to a local manager:

• Passes

only the NC commands that are addressed to a remote

modem

from its NC IN port to the in-band secondary channel

• Passes only responses

that are addressed

from a remote modem

to the local manager

from the secondary channel to its NC OUT

port.

With this option, a remote modem receiving the local modem’s
commands does not pass them to its NC OUT port

*NP1

A local modem, connected through its network control In (NC IN)
port to a local manager,:

• Passes

only the NC commands that are addressed to the location

(local a100)

from its NC IN port to the in-band

secondary channel

• Passes only responses

that are addressed

from a remote modem

to the local manager

from the secondary channel to its NC OUT

port.

*NP2

A local modem, connected through its network control-in (NC IN)
port to a local manager, passes

all

NC commands to and from a

remote modem, without filtering.

The remote modem operates the same way.

Summary of Contents for 3460












































































































































































Search results

Summary of Contents for 3460

Reviews:

Raymar 3460, User Manual, Page: 65 / 171

Search results

Summary of Contents for 3460

Reviews: