RaycoWylie i4507 Instruction Manual Download

Page: 74 / 78

55M4507OBE00-B

i4507 Offshore Lattice Boom Crane

Instruction Manual

•

Place the crane where it won’t get in the way of other equipment or operations

in the area.

• Block all controls and ensure all operating features are secured from

inadvertent motion.

• Make sure the starting means are inoperative.

• Lower the boom to the ground, if possible, or otherwise secure against

dropping

• Lower the block to the ground or otherwise secure against dropping

• Release hydraulic pressure from all hydraulic circuits before loosening or

removing hydraulic components

• “Warning” or “Out of Order” signs shall be placed on the crane controls and be

removed only by authorized personnel.

•

After adjustments and repairs have been made, the crane shall not be used until

all safety devices are reactivated and trapped air removed from the hydraulic
system. The instructions for the removal of air from hydraulic circuits should
be provided by the crane manufacturer.

6.5 Maintenance Procedure

Before starting repairs or adjustments on a crane,

you should take the following precautions.

Summary of Contents for i4507















































































Search results

Summary of Contents for i4507

Reviews:

Related manuals for i4507

Brands by name

Popular brands

RaycoWylie i4507, Instruction Manual

Search results

Summary of Contents for i4507

Reviews:

Related manuals for i4507

Brands by name

Popular brands