RaycoWylie i4507 Instruction Manual Download

Page: 61 / 78

i4507 Offshore Lattice Boom Crane

Instruction Manual

55M4507OBE00-B

5.2 Angle Sensor

Press the Select button when

«Angle 1»

is highlighted to see the software

version of the angle sensor and it’s calibration state. The displayed

information will look like this:

The second line indicates the software

version of the angle/length sensor and also

its creation date.

The following values will allow the

RaycoWylie technician to diagnose a

problem coming from the sensor.

If the angle sensor is not functioning properly, note these values and give them to

RaycoWylie

technician.

Press the

Escape

button to return to the main screen of the

diagnostic mode.

5.3 Load Sensor

To see the software version of the load sensor and its calibration state, press the

Select

button when Load 1 is highlighted

Summary of Contents for i4507















































































Search results

Summary of Contents for i4507

Reviews:

Related manuals for i4507

Brands by name

Popular brands

RaycoWylie i4507, Instruction Manual

Search results

Summary of Contents for i4507

Reviews:

Related manuals for i4507

Brands by name

Popular brands