RaycoWylie i4507 Instruction Manual Download

Page: 22 / 78

55M4507OBE00-B

i4507 Offshore Lattice Boom Crane

Instruction Manual

WARNING LIGHT

When operating within normal conditions the green LED warning light turns

on. The yellow warning light turns on to indicate that a set operating limit is

being approached. The red warning light turns on to warn the operator that an

abnormal condition has occurred.

2.2 Display Box Overview

MULTIFUNCTION

KEYS

MULTIFUNCTION

KEYS

GRAPHIC DISPLAY

This menu driven communication interface allows access to the various menus

and options to control the i4507 unit system.

MULTIFUNCTION BUTTONS

Each of these buttons allows you to select and/or execute the indicated function

displayed on the screen in any given window.This way the task performed by a

given multifunction button will vary depending on the menu or window.

FUNCTION DESCRIPTION

INTERNAL

BUZZER

WARNING LIGHT

(THREE COLORS)

Summary of Contents for i4507















































































Search results

Summary of Contents for i4507

Reviews:

Related manuals for i4507

Brands by name

Popular brands

RaycoWylie i4507, Instruction Manual

Search results

Summary of Contents for i4507

Reviews:

Related manuals for i4507

Brands by name

Popular brands