Raven RoGator 64 Series Installation Manual Download Page 52

Page: 52 / 80

HAPTER

RoGator 64/74/86/SS Series AutoBoom Installation Manual

TABLE 3. Ultrasonic Sensor Bracket Installation Kit (P/N 117-0131-082)

Picture

Item Description

Part Number

Qty.

Not Pictured

Sheet - AutoBoom Sensor Extension

016-0130-070

Bracket - 12” S-Type AutoBoom Sensor

063-0131-592

Bolt - 5/16”-18 x 1-1/4” Hex

311-0052-106

Nut - 5/16”-18 Nylon Insert Lock

312-4000-059

Washer - 5/16” Zinc Flat

313-2300-012

TABLE 4. Optional Wheel Kit 90’ - 100’ Booms (P/N 117-0133-001)

Picture

Item Description

Part Number

Qty.

Axle Assembly - Right Cushioned

AutoBoom

063-0131-585

Axle Assembly - Left Cushioned

AutoBoom

063-0131-590

Bracket - Weldment Left

116-0159-609

Bracket - Weldment Right

116-0159-610

Bracket - Hub Retainer

107-0171-617

Summary of Contents for RoGator 64 Series
















































































Search results

Summary of Contents for RoGator 64 Series

Reviews:

Related manuals for RoGator 64 Series

Brands by name

Popular brands

Raven RoGator 64 Series, Installation Manual

Search results

Summary of Contents for RoGator 64 Series

Reviews:

Related manuals for RoGator 64 Series

Brands by name

Popular brands