137
ENGLISH
6 SHIPPING AND
INSTALLATION
6.1 SAFETY WARNINGS FOR
TRANSPORTATION AND
INSTALLATION
The appliance must be installed by a qualified
technician, who must issue a declaration of
conformity of the system to the purchaser, taking
full responsibility for appliance installation and
correct operation.
The appliance installation site must be chosen
so that the generated heat can spread evenly
throughout the rooms that you wish to heat.
During transport and storage, avoid exposure to
rain or persistent humidity.
The appliance needs to be connected to a
single chimney that guarantees the draught
declared by the Manufacturer and observes
the installation regulations that apply to the
installation site.
The room where the appliance is installed must
have an air intake.
The air vent must be installed in such a way that
it can not be blocked.
The Manufacturer will not be held liable for
installation that is not compliant with the laws in
force, incorrect air circulation in the rooms and
inappropriate use of the appliance.
In particular, it is necessary:
• that the appliance be connected to a smoke
evacuation system duly sized to guarantee
the draught declared by the Manufacturer,
that is tight and observes the distances from
flammable materials;
• that there is a suitable combustion air intake in
compliance with the type of installed product;
• that other installed combustion appliances or
devices do not create a vacuum in the room
where the appliance is installed;
• that the safety distances from flammable
materials are observed.
Verification of system compatibility has a priority
over any other assembly or installation operation.
Local administrative regulations and particular
requirements of the authorities pertaining to
the installation of combustion appliances, the air
intake and the smoke evacuation system, may
vary based on region or nation. Check with your
local authorities if there are stricter laws than set
forth herein.
6.1.1 Packaging
When the appliance arrives, check:
• that it is the model you ordered;
• that it has not been damaged during shipping.
Any complaints must be reported to the
deliveryman (also on the delivery note) upon
receival.
Check the capacity of the floor before handling
and positioning the appliance.
The appliance always needs to be handled
vertically. Take extra care to protect the door and
its glass against mechanical impact that could
jeopardise their integrity.
To unpack the appliance, follow the procedure
described below:
1) Remove the side straps by unscrewing the
Pellet feed
gearmotor
failure
If the gear motor fails, the
product shuts down safely
and the corresponding
alarm is displayed
Cleaning
system gear
motor failure
If the gear motor fails, the
product shuts down safely
and the corresponding
alarm is displayed
Temporary
power failure
If a power failure occurs
during operation, when
the power returns the
temperature in the
combustion chamber is
checked and, if necessary,
the stove goes into cooling
mode
No ignition
If no flame develops during
the ignition phase, the stove
goes into alarm
It is forbidden to tamper with the safety
devices. Restarting the product is only possible
after eliminating the cause that caused the
intervention of the safety system. To understand
which anomaly occurs, consult this manual which
explains, depending on the alarm message that
the device displays, how to intervene on it.
If the problem persists, contact the Support
Service.
5.9.1 Minimum clearances from
combustible materials
SIDE
DISTANCE
X1 right
200 mm
X2 left
200 mm
Y2 rear
200 mm
Y1 front
> 1000 mm
Z ceiling
800 mm
Fig. 5.6
Summary of Contents for BLOCK 7 STONE
