Rangemaster Elite 110 Dual Fuel, User Manual

Page: 34 / 40

34
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Servicing
When servicing or replacing gas carrying components
disconnect from gas before commencing operation and
check appliance is gas sound after completion. When
checking for gas leaks use a liquid leak detector at all joints
and connections to check for leaks in the system. Use a
product specifically manufactured for leak detection. In GB
refer to BS 6891.
Leak testing of the appliance shall be conducted in
accordance to the manufacturer’s instructions.
CAUTION: DO NOT USE A FLAME TO CHECK FOR GAS
LEAKS.
Do not use re-conditioned or unauthorised gas controls.
Disconnect from the electricity supply before commencing
servicing, particularly before removing any of the following:
- control panel, side panels, hotplate tray or any electrical
components or covers.
Before electrical re-connection, check that the appliance is
electrically safe.
Note - References to LH and RH oven apply as viewed from
the front.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS.
TURN OFF THE GAS SUPPLY
1 To Remove the Control Panel
Disconnect from the electricity supply.
Remove the pan supports and control knobs. Remove the 3
screws at the rear of the top edge of the control panel.
Open the oven doors and remove the 2 fixing screws, one
at each end, underneath the control panel. Lift the control
panel, pull forward and disconnect the wiring from the rear.
Replace in reverse order.
A Control panel top fixing screws
B Hotplate front fixing screws
C Hotplate back fixing screws
2 To Remove the Hotplate top
Disconnect from the electricity supply.
Pull cooker forward to gain access.
Remove the control panel see 1. Remove the hotplate
burner caps and tops. If there are screws holding the
hotplate burners to the hotplate, remove them (not the
spark electrode fixing screws). Remove the 2 hexagon
headed rear hotplate fixing screws and the 3 front hotplate
fixing screws. Lift the hotplate clear of the appliance.
Replace in reverse order.
3 To Remove an Outer Side Panel
Disconnect from the electricity supply.
Remove the control panel – see 1. Remove the retaining
screw on the upper front edge and the two fixings on the
rear or the side panel. Undo the lower retaining screw
situated below the edge at the panel front corner. Remove
the panel by pulling it away from the unit.
4 To Remove an Oven Neon
Remove the control panel – see 1. Hold the lens in position
at front of the panel and from the rear pull the body of the
neon out of the front lens. Hold the front lens in position
and from the rear of the control panel fit the new light
to the lens. Replace parts in reverse order. Ensure the
replacement neon functions correctly.
5 To Remove the Clock
Remove the control panel - see 1.
Pull off the timer control button(s). Remove the timer/
mounting bracket assembly from the facia by removing the
fixing screws. Remove the timer from its mounting bracket
by depressing the plastic lugs on the timer case, at the same
time pulling the unit forward. Reassemble in reverse order.
When replacing leads refer to the wiring diagram. Check
operation of timer.
6 To Remove a Thermostat
Disconnect from the electricity supply.
Remove the hotplate – see 2. Open the appropriate oven
door and remove the oven shelves.
RH oven
Remove the two fixings that secure the thermostat phial
cover. Unclip the thermostat phial from the clips in the oven
back panel.
LH oven
Remove the two screws holding the thermostat phial to
the oven fan cover at the rear of the oven. Pull the unit
forward to access the rear of the cooker. Remove the both
cover boxes by removing the fixing screws and lifting clear.
Feed the thermostat capillary clear of the oven. Disconnect
the wires from the thermostat and undo the two fixings
that secure the control to the mounting plate. Fit the
replacement and re-assemble in reverse order. Ensure that
the phial is clipped to the oven rear, positioned centrally
between the clips. Check that the thermostat functions
correctly.