manualshive.com logo in svg

RAMSET Twist Lok TS60P, Instruction Manual

Share
Download
RAMSET Twist Lok TS60P Instruction Manual Download Page 25

25

25

4.

 Reassemble barrel and magazine into upper 

tool assembly as detailed in point 5 in 
Operators Service Procedure - Reassembly 
pages 22 and 23 

(Pic. 35)

.

Pic. 35

5.

 The tool should be dry cycle tested to ensure 

it is functioning correctly. The magazine will 
need to have pins loaded, to enable the dry 
cycle test to be carried out. Ensure 

no power 

load strip

 is loaded into the tool. Press the 

tool against the work surface and pull the 
trigger, listen for the sound of the firing pin 
dropping. Repeat this test a number of times 
to check consistency.

SAFETY WARNINGS

When a TM40 magazine is 
fitted to a standard Twist 
Lok

TM

 Tool a new special 

piston is required to ensure 
the magazine is not damaged 
during normal operation.
Never attempt to disassemble 
the TM40 magazine, it should 
only be dismantled and 
inspected by your authorised 
Ramset repair technician.

Installation of TM40 Magazine for Twist Lok

TM 

Tools cont.

Summary of Contents for Twist Lok TS60P































Reviews:

No comments

Brands by name

Popular brands

Load more brands