Raider RD-GWP04, User Manual

Page: 17 / 90

17
Replace en -
gine oil
For the first
change only - after
the first month or
after 20 hours of
work
●
Air cleaner
check
●
Air cleaner for
clean
● ●
Spark plug
Fuel supply Replace per every two years
Wane wheel
●
Pump case
cover
●
Water inlet
●
9.1. Change the engine oil.
The oil is drained more easily when the engine is warm. Unscrewed the cap for refilling with oil level measuring stick for
checking oil (4) and wipe it. Unscrewed and stopper for draining the oil from the crankcase (3) and drain the spent motor
oil into a suitable container. Take care of the environment when dispose of spent oil from the engine. Recommendations
to collect spent oil container to be sent to the appropriate site for disposal or recycling center. After the spent oil drain back
Screw stopper for draining the oil from the crankcase (3). Pour the recommended clean oil through a hole for screwing of
the cap for refilling with oil level measuring stick “(4) until the oil level reaches the thread. Make sure the oil has reached
the desired level. Screw ‘cap for refilling with oil level measuring stick “(4). Clean hands of the oil they have been in contact
with him.
9.2. Cleaning the air filter. Do not use the pump with dirty air filter. The dust and small particles that can suck the engine
will shorten its operational life. Unscrewed nut (10) to cover the air filter (11) and washers and remove the lid of the filter.
Remove the air filter. Clean the filter with non-flammable solvent or with such a high flash point and allow to dry completely
after cleaning. Do not clean the air filter with flammable liquids, may occur because of fire or explosion under certain
conditions. Insert the air filter back into place. Replace the washer and the lid of the filter and screw the nut (10).
9.3. Keeping the candle (22).
The recommended type of spark plug is F7TC. To ensure normal operation of the engine, the spark plug must have
adequate distance between the electrodes and must be cleaned of deposits. Remove the “pipe” of the candle (21), and pull
the handle on the top and end. Under no circumstances remove “pipe” with the tug of the cord (20). Muffler can be very hot
if the engine was working. Be careful not to touch the exhaust pipe (9). With the aid of keys (25) to unwrap the candle and
(26) unscrewed the spark plug (22). Visually check the spark plug. Dispose of the candle if it is apparent insulation is worn
or broken or cracked. “Check and sealing O-ring (29). If the candle is in excellent condition and clean it with a brush and
Screw it back into the cylinder head. Screwing in a new spark plug, tighten an additional 1 / 2 turn after the spark plug up
and pressed O-rings (29). Make sure the candle is properly tightened. Improper tightening may cause overheating of the
engine and its failure. Use candles only of that type.
10. Transport and storage.
To avoid risk of fire engines have to wait to cool before being transported to the pump.
10.1. Make sure that the storage is not wet or dusty.
10.2. Clean the inside of the pump. The pump can be blocked, if used to drain water containing soil, sand or heavier
particles. Before harvesting and storage, clean the pump by suction of pure water. After cleaning, unscrew the stopper for
the drain water (18) and drain it. Then Screw stopper for draining (18). Drain water from the pump is required for storage at
low temperatures and will protect her from serious injury.
10.3. To keep the engine in a planned longer stay. Unscrewed the spark plug (22), pour one tablespoon pure motor oil
in the cylinder, turn the engine several times to even distribution of oil and then plug Screw (22) again.
10.4. Cover the pump to protect from dust.
11. Deficiencies and ways to remedy them. Table.