Rae MiniRAE Lite User Manual Download Page 61

Page: 61 / 76

MiniRAE Lite User’s Guide

Troubleshooting

Problem

Possible Reasons & Solutions

Cannot turn on power
after charging the
battery

Reasons:

Discharged battery.
Defective battery.

Solutions:

Charge or replace battery.

Lost password

Solutions:

Call Technical Support at +1
408-752-0723 or toll-free at
+1 888-723-4800

Reading abnormally
High

Reasons:

Dirty filter.
Dirty sensor module.
Excessive moisture and
water condensation.

Incorrect calibration.

Solutions:

Replace

filter.

Blow-dry the sensor module

Calibrate the unit.

Reading abnormally
Low

Reasons:

Dirty filter.
Dirty sensor module.
Weak or dirty lamp.
Incorrect calibration.

Solutions:

Replace filter.
Remove Calibration
Adapter.
Calibrate the unit.
Check for air leakage.

Buzzer
Inoperative

Reasons:

Bad buzzer.

Solutions:

Check that buzzer is not
turned off.

Call authorized service

center.

Summary of Contents for MiniRAE Lite












































































Search results

Summary of Contents for MiniRAE Lite

Reviews:

Brands by name

Popular brands

Rae MiniRAE Lite, User Manual

Search results

Summary of Contents for MiniRAE Lite

Reviews:

Brands by name

Popular brands