manualshive.com logo in svg

Rae MiniRAE Lite, User Manual

Share
Download
Rae MiniRAE Lite User Manual Download Page 6

MiniRAE Lite User’s Guide 

Read Before Operating 

 

This manual must be carefully read by all individuals who have or 
will have the responsibility of using, maintaining, or servicing this 
product. The product will perform as designed only if it is used, 
maintained, and serviced in accordance with the manufacturer’s 
instructions. The user should understand how to set the correct 
parameters and interpret the obtained results. 
 

CAUTION! 

To reduce the risk of electric shock, turn the power off before 
removing the instrument cover. Disconnect the battery before 
removing sensor module for service. Never operate the instrument 
when the cover is removed. Remove instrument cover and sensor 
module only in an area known to be non-hazardous. 

 

Intrinsic Safety: 

 

US and Canada: Class I, Division 1, Group A, B, C, D, T4 

 

 

0575   II 2G EEx ia II C T4 

KEMA 07 ATEX 0127 
-20º 

≤

 T

amb

 

≤

 50º C 

 
 
 
 

4 

Summary of Contents for MiniRAE Lite













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands