manualshive.com logo in svg

Rae MiniRAE Lite, User Manual

Share
Download
Rae MiniRAE Lite User Manual Download Page 54

MiniRAE Lite User’s Guide 

31 Maintenance 

The major maintenance items of the instrument are: 
 

•

 

Battery pack 

•

 

Sensor module 

•

 

PID lamp 

•

 

Sampling pump  

•

 

Inlet connectors and filters 

Note: 

Maintenance should be performed by qualified personnel 

only. 

  

NOTE: 

The printed circuit board of the instrument is connected to 

the battery pack even if the power is turned off. Therefore, it is very 
important to disconnect the battery pack before servicing or replacing 
any components inside the instrument. Severe damage to the printed 
circuit board or battery may occur if the battery pack is not 
disconnected before servicing the unit.

  

Battery Charging & Replacement 

When the display shows a flashing empty battery icon, the battery 
requires recharging. It is recommended to recharge the instrument 
upon returning from fieldwork. A fully charged battery runs a 
instrument for 16 hours continuously. The charging time is less than 8 
hours for a fully discharged battery. The battery may be replaced in 
the field (in areas known to be non-hazardous), if required. 
 

WARNING! 

To reduce the risk of ignition of hazardous atmospheres, recharge 
battery only in area known to be non-hazardous

. 

Remove and 

replace battery only in areas known to be non-hazardous. 

 

52 

Summary of Contents for MiniRAE Lite













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands