manualshive.com logo in svg

Rae MiniRAE Lite, User Manual

Share
Download
Rae MiniRAE Lite User Manual Download Page 16

MiniRAE Lite User’s Guide 

6 

Charging A Lithium Ion Battery 

 
Always fully charge the battery before using the instrument. The 
instrument’s Li-ion battery is charged by attaching the instrument to 
the Travel Charger (or by placing the instrument in the optional 
Charger Stand). Contacts on the bottom of the instrument meet the 
Travel Charger’s (or Charger Stand’s) contacts, transferring power 
without other connections. 
 

Note:

 Before connecting the Travel Charger to the instrument, 

visually inspect the contacts to make sure they are clean. If they are 
not, wipe them with a soft cloth. Do not use solvents or cleaners. 
 
Follow this procedure to charge the instrument: 

 

1. Plug the AC/DC adapter’s barrel connector into the 

instrument’s Charger Stand or Travel Charger. 

 

 

2. Plug the AC/DC adapter into the wall outlet. 

 

3. Connect the AC/DC adapter to the Travel Charger (or 
    Charger Stand). 

 

3. Place the instrument into the Travel Charger or Charger Stand. 
The LED in the Travel Charger (or Charger Stand) should glow. 

 
The instrument begins charging automatically. (If the optional 
Charger Stand is used, the “Primary” LED blinks green to 
indicate charging.) During charging, the diagonal lines in the 
battery icon on the instrument’s display are animated and you see the 
message “Charging...” 
 
When the instrument’s battery is fully charged, the battery icon 
is no longer animated and shows a full battery. The message 
“Fully charged!” is shown. (If the Charger Stand or Travel 
Charger is used, its LED glows continuously green.) 

14 

Summary of Contents for MiniRAE Lite













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands