Rae MiniRAE Lite User Manual Download Page 11

Page: 11 / 76

MiniRAE Lite User’s Guide

3 Physical

Description

The main components of the portable VOC monitoring
instrument include:

•

Three keys for user to interact with the instrument:
3 operation/programming keys for normal operation or
programming

•

LCD display with back light for direct readout and calculated
measurements

•

Built-in flashlight for illuminating testing points in dark
environments

•

Buzzer and red LEDs for alarm signaling whenever exposures
exceed preset limits

•

Charge contacts for plugging directly to its charging station

•

Gas entry and exit ports

•

USB communication port for PC interface

•

Protective rubber cover

4 Specifications

Size:

9.25" L x 3.6" W x 2.9" H

Weight:

28 oz with battery pack

Detector:

Photoionization sensor with 10.6 eV UV
lamp

Battery:

Rechargeable Lithium-Ion battery pack
(snap in, field replaceable)

Alkaline battery holder (for 4 AA batteries)

Battery Charging

Less than 8 hours to full charge

Operating Hours:

Up to 12 hours continuous operation

Display:

Large dot matrix screen with backlight

Summary of Contents for MiniRAE Lite












































































Search results

Summary of Contents for MiniRAE Lite

Reviews:

Brands by name

Popular brands

Rae MiniRAE Lite, User Manual

Search results

Summary of Contents for MiniRAE Lite

Reviews:

Brands by name

Popular brands