Radyne DMD20 LBST Installation And Operation Manual Download Page 147

Page: 147 / 306

DMD20/20LBST Universal Satellite Modem

User Interfaces

MN-DMD20-20LBST Revision 14

4–39

SERVER IP ADDR

{XXX.XXX.XXX.XXX} Hexidecimal Address

{ddd.ddd.ddd.ddd} Decimal Address

The IP Address of the Boot Server and the address of the SNMP

Trap Server when SNMP is active. If a server is used and there

is no local router, this address must be consistent with the

modem address. If a router has been specified, the address is

presumed to be reachable via the router. Broadcast and loop

back addresses will not be allowed. These are addresses with

all subnet bits set to 0’s or 1’s.

ROUTER IP ADDR

{XXX.XXX.XXX.XXX} Hexidecimal Address

{ddd.ddd.ddd.ddd} Decimal Address

The IP Address of the Local Network Router. If a router is

present on the local network, this address must be consistent

with the IP Mask and the subnet of the modem. If no router is

present, then the address should be set to a foreign address.

This address is expressed in hexadecimal format.

Broadcast and loop back addresses will not be allowed. These

are addresses with all subnet bits set to 0’s or 1’s.

To change the display for the IP ADDRESS MASK, MODEM IP ADDRESS,
SERVER IP ADDRESS, AND ROUTER IP ADDRESS, press all four arrow keys
simultaneously.

MODEM EADDR

{001065010000}

Displays the Ethernet address of the device. Set at the factory

and is a unique identifier for the Ethernet physical interface.

ETHER RATE

{10 MBPS/HD}

The data rate for the local Ethernet Interface.

10 Mbps/HD – for 10 Base-T in either half-duplex or full duplex.

SNMP (menu)

A description of OID organization is provided in the MIB portion

of this manual (Appendix C).

SNMP VERSION

{V1 & V2, V3}

This selection controls the SNMP Version that will be used in

messaging between the equipment and its host.

When V1 & V2 is used, RD COMMUNITY and RDWR

COMMUNITY are used to determine the authorization of an

incoming message.

When V3 is used, three contexts are supported:

public

mib2

and

dev

. Context, Authentication and Privacy are a portion of

each SNMPV3 message.

The

public

context will only allow the user to see the sysoid of

the unit. This is the most restricted access possible and only

allows the unit to be identified by a host SNMP Station.

The

mib2

context allows a user with appropriate authentication

to access the mib2 OIDs and the SNMP OIDs. These are of

interest primarily to network operators not controlling the satellite

link.

IMPORTANT

Summary of Contents for DMD20 LBST



















































































































































































































































































































Search results

Summary of Contents for DMD20 LBST

Reviews:

Related manuals for DMD20 LBST

Brands by name

Popular brands

Radyne DMD20 LBST, Installation And Operation Manual

Search results

Summary of Contents for DMD20 LBST

Reviews:

Related manuals for DMD20 LBST

Brands by name

Popular brands