Radionics D7000 Series Operation And Installation Manual Download

Page: 8 / 67

D9000/D7000 Series Operation & Installation Manual

Page 8

74-07692-000-C 4/97

Communicator

The Control/Communicator uses a built-in digital
communicator to send reports to the receiver. The
panel transmits reports in either the Modem IIIa

or BFSK format. Your D6500 receiver's MPU

and line cards must have software revision 8.00
(or greater) installed to accept Modem IIIa

2 TM

reports from the panel. Power your receiver down
and up to print the software revision numbers.

The panel connects to an RJ31X jack for phone
line seizure. Connection to the RJ31X complies
with FCC regulations for using the public
telephone network. You can program the panel to
direct reports to four separate phone numbers.
Adding the D928 Dual Phone Line Switcher
module allows you to connect and supervise a
second phone line.

The system has routing capabilities that allow you
to direct groups of event reports to four different
destinations. Each of the report groups can be
programmed to report to one or more of the
destinations. Primary and backup reporting paths
can be programmed for each of the destinations
and each of the report groups. A custom option
allows you to specify individual event reports to
be sent.

Command Centers

You can connect a maximum of 32 Command
Centers unsupervised to the system. The
available power, number of supervised
Command Centers, and number of areas you
intend to use, affect the total number of Command
Centers you can connect.

The system can supervise up to 8 Command
Centers. The panel transmits a serial device
trouble report,

SDI FAILURE

in the Modem IIIa

2 TM

format or

TROUBLE ZN D

in the BFSK format, if it

loses communication with a supervised
Command Center. You can add more Command
Centers but only eight can be supervised. Table 1
shows the Command Centers compatible with the
D9000/D7000 Series Control/Communicators.
See

Command Center in the D9000/D7000

Series Program Entry Guide (74-07695-000) for
complete details on programming Command
Center options.

Table 1: Compatible Command Centers

Keyswitch

You can arm and disarm any of the eight
available areas with maintained or momentary
closure devices such as keyswitches and sub-
control units (D279). Point programming
determines loop responses and which area a
keyswitch controls.

Access Control

The D9412 can control eight access doors (each
requiring the optional D9210B Access Control
Module) with up to 996 uniquely identified cards/
tokens. The D7412 can control two access doors
with up to 396 uniquely identified cards/tokens.
Access can be granted from a Weigand style
access control device (card reader) connected to
the D9210B Access Control Module. Access may
also be granted from a “request to enter” or a
“request to exit” input, or from a Command
Center.

The access control features of the D9412 and
D7412 can deny access during armed periods. It
can also grant access only to certain authorized
users depending on whether the area is master
armed, perimeter armed, or disarmed. The alarm
system can also be programmed to automatically
disarm when designated authorized users are
granted access.

Event Memory

The system uses event memory to store events
for each area. You can view the events for an
area at a D1255 Command Center assigned to
the area. The panel clears the events for an area
from event memory and starts storing new events
when you master arm the area.

Event Log

The system stores from 500 to 1000 events and
event modifiers from all areas in it's event log.
Event modifiers add information about an event
to the log. Some events are always followed by a
modifier. For example, the system adds at least
two items to the log each time you arm or disarm
an area, the open (or close) event and an event
modifier showing the previous arming state.

All events and their modifiers can be stored even
if the panel does not send a report for them. You
can view the log at a D1255 Command Center,
print it locally using the D9131A Parallel Printer
Interface and a parallel printer, or upload it to the
Remote Account Manager (RAM III).

See the appendix in the

User’s Guide for a listing

of log events and event modifiers.

♦

Model

Display

Application

D1255

16-character alpha-numeric

Fire/Burglary/Access

D720

8 LED