background image

13

1143923-W2-E

Rada V10 Concealed

1. 

Carefully remove the concealing cap from the 

control lever.

2.

  Unscrew the grubscrew using a 2.5 mm 

hexagonal key (supplied) and pull off the 

control lever(s).

 

Note! 

The flow control lever must be in the off 

position in order to remove it.

3. 

Carefully remove the concealing ring from the 

concealing plate.

4.

  Determine the route for the hot and cold 

supply pipework and for the outlet pipework. 

When connecting to the BIV shower fittings it 

is recommended that the outlet be positioned 

to one side of the mixer. This is to prevent 

the flexible hose from obstructing the shower 

controls (refer to illustration).

5.

  Mark the routes for the hot and cold supply 

pipework at 103 mm centres (

Hot - Left, Cold 

- Right

).

 

Note! 

If it is not possible to install the 

mixer with this pipework configuration follow 

instruction 6.

 

Falling Supplies:

 For falling supplies loosen 

the grubscrew on each elbow using the 2.5 mm 

hexagon key (supplied). Remove the elbows 

and install on opposite sides.

 

Important! 

Make sure that the elbows are 

pushed fully onto the mixer before tightening 

the grubscrews, 

do not 

overtighten.

Concealing Ring

Concealing Plate

Grubscrew

Concealing Cap

Control Lever

103 mm

Outlet Pipe BIV

Cold Inlet

Hot Inlet

Thermostatic 

Mixer

Alternative Pipe layouts

Outlet Pipe BIV

Summary of Contents for V10

























Reviews: