background image

14

Failures 

refers to EKCO.LN2 and EKCO.L2 boiler only

Symptom

Reason 

Action 

The indicators on 

control panel are off lack of boiler power supply

check parameters of the power network 

and fuses
contact an authorised service or the seller

A indicator flickers

insufficient pressure (below 0,5bar) switch the controller to the pressure view, 

increase the pressure to the required level 

pressure sensor failure 

switch the controller to pressure view, if 

the display shows „--” contact an author-

ised service

H indicator flickers

pump is blocked 

unblock  the  pump  -  unscrew  the  screw 

on  pump  housing  and  move  the  pump 

rotor manually 

a medium doesn’t circulate through 

the boiler – boiler is blocked 

an  air-bound  central  heating  system, 

vent the installation, pump and boiler
check patency of central heating system 

clean the filter

a failure of pump’s power supply  contact an authorised service or the seller
a failure of pump or flow sensor contact an authorised service or the seller

G indicator is off  

(in winter mode)

a  failure  of  installation  that  con-

nect a room thermostat

contact an authorised service or the seller 

a failure of electronic module 

contact an authorised service or the seller

K indicator flickers a  failure  of  inlet  temp.  sensor, 

boiler in failure condition 

contact an authorised service or the seller 

L indicator flickers  a  failure  of  outlet  temp.  sensor, 

the heating is blocked

contact an authorised service or the seller 

G indicator flickers, 

master appliance 

doesn’t work 

a  failure  of  installation  that  con-

nects the master appliance

contact an authorised service or the seller

a failure of electronic module

contact an authorised service or the seller

EKCO.LN2 and 

EKCO.L2 model 

doesn’t heat the 

cylinder

a failure of cylinder temp. sensor 

or thermostat  

contact an authorised service, replace cyl-

inder temp. sensor or thermostat

a failure of three-way  valve ser-

vo-motor

replace servo-motor

a failure of electronic module 

contact an authorised service or the seller

EE message on E 

display

data record error 

contact an authorised service or the seller

Summary of Contents for EKCO.L2

















Reviews: