background image

Open over the front driver and pas-

senger  compartments: 

FIG 60

FIG 61

FIG 62

Option  #1  &  #2                                                                                 

Fully Open Front and Rear Passen-

ger “Sun Roof”: 

Option #3 & #4

FIG 63

Unlatch the two front Windshield latch

-

es (Fig 60 & 61).  Push the front head-

er up and over to open the “sunroof”.  

When you open the front portion there 

will be fabric still hanging down over 

your head(Fig 62)  This is Option #1 

which provides protection from the sun 

while opens the “sunroof”.  If you push 

the fabric up in the center of the folded 

back “sunroof” and tuck/ fold it under 

the header, this is option #2 which 

opens up the “sun roof” completely. 

This option is shown in Fig 62A.

These options open both the front cab 

and rear cab portions of the top.  This 

option requires you to remove the front 

header arms and the two bows from 

the bow mount brackets. Fig 63 shows 

the finished look of this “Sun Roof” 

option with the front header installed 

on the third bow bracket mount and the 

header folded  all the way back to the 

rear of the vehicle. 

SEE NEXT PAGE 

             

for options #3 & #4.                  

Your Soft top hardware has multiple 

front fold back options. Depending 

on how much sun and weather you 

want to let into the cab determines 

the options available to you

Using Your Fastback Soft Top

12

FIG 62A

Summary of Contents for QuadraTop 11113.2335
















Reviews: