background image

13

FIG 64

FIG 66

Using Your Fastback Soft Top 

Continued 

Fully Open Front and Rear Passen-

ger “Sun Roof”:

With the header latches un-latched 

and front section open(Fig 64) un-hook 

the 2 quick release knobs located on 

the end of the header arms as circled 

in Fig 65.  Next, un-hook the 4 quick 

release knobs on bow #1 and bow 

#2 (Fig 65) leaving the two rear bows 

(Bow #1 & #2) encased in the hook 

and loop flaps.

Option #3 & #4

Once The front bow arms and two 

rear bows are disconnected from the 

bow mount brackets, with the help of 

a friend, carefully fold back the front 

header and two bows layering the top 

and bows under the fabric and then 

connect the front bow arms quick 

release brackets to the rear-most third 

bow mount bracket as 

shown

 in Fig 

66.

 

This is option # 3. Notice in Fig 67

 

how 

the fabric is “layered back and the

 

front 

Bow Mount Brackets are installed

 

to 

the rear bow brackets.  This is op

tion 

#4 with the entire fabric assembly

 

folded back and secured to the rear

 

brackets.

FIG 65

FIG 67

The front header arms must be secure to the third bow mount bracket and the 

fabric/ bows must be layered back before the vehicle is driven!  Failure to secu-

re these bow mounts will cause the top to potentially fly off the vehicle causing 

damage to the top, vehicle and potentially other vehicles on the road. 

WARNING

Summary of Contents for QuadraTop 11113.2335
















Reviews: