background image

Important Safety information

Your QuadraTop® Fabric Replacement 

Top is intended to be used with other 

QuadraTop Products to increase the 

fair weather enjoyment of your off-road 

capable vehicle. Before installation,

please take a moment to review the 

following safety information and installa

-

tion instructions. Important safety infor

-

mation is generally preceded by one of 

three signal words indicating the relative 

risk of injury.

The signal words mean.

a hazardous situation which, if not avoided, could result in death or serious in-

jury. You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions.

WARNING

CAUTION

NOTICE

a hazardous situation which, if not avoided, could result in minor or moderate 

injury. You CAN be moderately HURT and also may suffer property damage if 

you don’t follow instructions.

Careful attention is required to this instruction or operation but does general-

ly not relate to personal injury. Damage to your Quadratec® product or other 

property may result if you don’t follow instructions.

Before you begin Installation:

We are excited that you have chosen 

the Adventure Top. This high-quality soft 

top is designed to provide protection 

from the elements and a stylish look 

on your Jeep®. Please note that it is 

important that you become familiar with 

the installation process of this top by 

reading the following instruction sheet 

and warnings thoroughly. 

For a smooth fit and ease of installation, this top should be installed at tem

-

peratures above 72 degrees. Below this temperature, the fabric may contract an 

inch or more making it difficult to install. We highly recommend taking the top 

out of the package and letting it sit inside a warm place or direct sunlight for 

1-2 hours before you install the top. When warm, this top will install quickly.

NOTICE

2

Once the components are removed 

from the shipping box, locate the front 

and rear door surround components 

and accessories as shown in FIG1.

FIG 1

4mm Allen Wrench

Allen Head 

Screws  for 

Door Surrounds

Allen Head 

Screws for 

Brackets

Door Surround 

rear Brackets

Rear Bracket 

screws 12mm 

with Nuts

Left

Right

Left

Right

Rubber 

Seal

Carefully 

organize the door surround 

components

 as  shown in Fig.1 making 

sure the passenger side and driver’s 

side components are separated.

When unpacking, carefully check to 

make sure all parts are included. If any 

part is missing or broken, please call 

Quadratec customer service at 800-745-

6037.

Step 1: Un-packing & Organizing the Door Surrounds: 

Put on safety glasses. Carefully remove all the contents of the large shipping 

box onto a table top or onto the gro

und

 on top of a soft towel.

Knobs

Driver Side Door Surround 

Passenger Side Door Surround 

Summary of Contents for QuadraTop 11113.2335
















Reviews: