background image

15

January 8, 2019

7082-154E

TREKKER INSERT

Figure 15.2

Figure 15.1 - Fire pot with large clinker

Clinker

C. General Maintenance and Cleaning

1.  Cleaning Fire pot using Lever

•  Frequency:

 Daily or as needed*

•  By:

 Homeowner

a.  Be sure the appliance is allowed to cool.

b. 

Open cast face of appliance

c. 

Pull fire pot floor cleaning lever two times until the 

ash falls into the ash pan below 

(Figure 15.2)

.

d. 

It may be necessary to use your fire pot clean-out 

tool to chip away material that has built up on the 

sides of the fire pot and to push out any clinkers 

(Figure 15.1)

.

e. 

Larger clinkers may have to be removed from the 

top of the fire pot.

f. 

If the clinker adheres to the sides of the fire pot, 

you will need to manually clean the fire pot. The fire 

pot floor plate must be fully closed when finished.

2.  Cleaning Ash Pan

•  Frequency:

 Weekly or every 3-5 bags

•  By:

 Homeowner

a. 

Locate the ash pan underneath the fire pot.

b.  Slide the ash pan straight out.

c. 

Empty into a non-combustible container and re-

install ash pan.

d.  When replacing ash pan push it back until it 

catches on the 2 side latches.

Clinkers filling the ash pan will have to be cleaned out more 

often than ash.

Ash Disposal:

Ashes should be placed in a steel container with a tight-

fitting lid. The container of ashes should be moved outdoors 

immediately and placed on a non-combustible floor or on 

the ground, well away from combustible materials, pending 

final disposal.

If the ashes are disposed of by burial in soil or otherwise 

locally dispersed, they should be retained in the closed 

container until all cinders have thoroughly cooled. Other 

waste shall not be placed in this container.

3.  Ash Removal from Firebox

•  Frequency:

 Weekly or more frequently depending on 

ash build-up

•  By:

 Homeowner

a.  Be sure the appliance is allowed to cool.

b. 

There must not be any hot ashes in the firebox 

during cleaning.

c. 

Frequent cleaning of the ash in the firebox with a 

vacuum cleaner will help slow down the build-up of 

ash in the exhaust blower and vent system.

RISK OF FIRE

Keep combustible materials, gasoline and other 

flammable vapors and liquids clear of appliance.

• 

Do NOT store flammable materials in the 

appliance’s vicinity.

• 

Do NOT use gasoline, lantern fuel, kerosene, 

charcoal lighter fluid or similar liquids to start 

or “freshen up” a fire in this heater.

Keep all such liquids well away from the heater 

while it is in use as combustible materials may 

ignite.

WARNING

Summary of Contents for TREKKER INSERT series



































Reviews: