background image

DO NOT DISCARD THIS MANUAL

NOTICE

• 

Important  operating 
a n d   m a i n t e n a n c e 
instructions included.

• 

Leave this manual with 
party  responsible  for 
use and operation.

• 

Read,  understand  and 
follow these instructions 
for safe installation and 
operation.

DO N

OT

DIS

CAR

D

WARNING

If the information in these 
instructions is not followed 

exactly, a fire may result causing 

property damage, personal injury, 

or death.

 

•  Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.

•  Do not overfire - If heater or chimney 

connector glows, you are overfiring. 

Overfiring will void your warranty.

•  Comply with all minimum clearances to 

combustibles as specified.  Failure to 

comply may cause house fire.

www.quadrafire.com  

4100- I ACT WOOD INSERT

Advanced Combustion Technology (ACT)

O-T L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

250-7201F

R

Installation and service of this appliance should 

be performed by qualified personnel.  Hearth & 

Home Technologies recommends NFI certified 

professionals, or technicians supervised by an 

NFI certified professional.

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overfire and generate 

poisonous gases (i.e. carbon monoxide).

Models:

4100I-GD-B
4100I-NL-B

April 19, 2010

HOT SURFACES!

Glass and other surfaces are 
hot  during  operation 

AND

 

cool down.

WARNING

Hot glass will cause burns.

•  Do not touch glass until it is cooled 

•   NEVER allow children to touch glass

•  Keep children away

•  CAREFULLY SUPERVISE children in the same room 

as  appliance

•   Alert children and adults to hazards of high 

temperatures

High temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other 

combustibles away. 

Summary of Contents for 4100-I ACT









































Reviews: