Quadlogic MiniCloset-5c Installation Manual Download Page 55

Page: 55 / 117

Chapter 4

Installation

Quadlogic Controls Corporation

The MCI runs CT terminals CT#1 to CT#24 with two terminals connected to Meter #1
(M#1) to Meter #12 (M#12). The number of CT terminal and meter connections will
depend on the number of suites available. For example,

- M#1 connects to CT#1 and CT#2

- M#2 connects to CT#3 and CT#4

- repeat for M#3 to M#1

After completing all current transformer terminations, connect four (4) current connectors
and then remove the twenty-four (24) shorting links.

Follow local codes for installation requirement, e.g. conduit, fused disconnect, distance,
and wiring.

Installation of 0.1A inputs and CL10 or 5A inputs are the same.

CAUTION:

If breakers are energized, shorting links must be installed before:

a) Disconnecting the CT headers or
b) Replacing or installing meter heads on the panel.

Bodily injury or damage may result if shorting links are not installed.

Summary of Contents for MiniCloset-5c
























































































Search results

Summary of Contents for MiniCloset-5c

Reviews:

Related manuals for MiniCloset-5c

Brands by name

Popular brands

Quadlogic MiniCloset-5c, Installation Manual

Search results

Summary of Contents for MiniCloset-5c

Reviews:

Related manuals for MiniCloset-5c

Brands by name

Popular brands