QNO FQR8030 User Manual Download Page 23

Page: 23 / 149

2WAN 4LAN Medium Scale Multi-WAN QoS Router

MTU

Input the packet maximum transmission unit of this
WAN

After the changes are completed, click

“Apply”

to save the configuration, or click

“Cancel"

to leave without making any changes.

Static IP

If ISP issue a static IP (such as one IP or eight IPs, etc.), please select this connection

mode and follow the steps below to input the IP numbers issued by ISP into the relevant

boxes.

Attention: Even if ISP offers a static IP address, it might be an automatic mode to

obtain a DHCP IP or to obtain a PPPoE dial-up IP. Although the IP address obtained will be

the same each time, users still must select the correct connecting mode!

WAN IP address:

Input the available static IP address issued by ISP.

Subnet Mask:

Input the subnet mask of the static IP address issued by ISP, such
as:

Issued eight static IP addresses: 255.255.255.248

Issued 16 static IP addresses: 255.255.255.240

Default Gateway:

Input the default gateway issued by ISP. For ADSL users, it is

usually an ATU-R IP address. As for optical fiber users, please

Summary of Contents for FQR8030






















































































































































Search results

Summary of Contents for FQR8030

Reviews:

Related manuals for FQR8030

Brands by name

Popular brands

QNO FQR8030, User Manual

Search results

Summary of Contents for FQR8030

Reviews:

Related manuals for FQR8030

Brands by name

Popular brands