manualshive.com logo in svg

Qlogic SilverStorm 9000, Reference Manual, Page: 39 / 210

Share
Download
Qlogic SilverStorm 9000 Reference Manual Download Page 39

2 – Switch Command Line Interface

Groups and Commands

D000025-002 Rev. A

2-33

A

Network

ifShow

Displays information for all the network interfaces for the switch, including the management port and 
the internal Ethernet network.

Syntax:

Options:

Sample Output:

ifShow [ifName]

[ifName]

The network interface name.

-> ifShow lo2 (unit number 0):
        Flags: (0x8069) UP LOOPBACK MULTICAST ARP RUNNING
        Type: SOFTWARE_LOOPBACK
        Internet address: 127.0.0.1
        Netmask 0xff000000 Subnetmask 0xff000000
        Net 0x7f000000 Subnet 0x7f000000
        Metric is 0
        Maximum Transfer Unit size is 32768
dp0 (mgmt_eth1 is active), (mgmt_eth2 is disabled):
        Flags: (0x8863) UP BROADCAST MULTICAST ARP RUNNING
        Type: ETHERNET_CSMACD
        Internet address: 172.26.0.221
        Broadcast address: 172.26.15.255
        Netmask 0xffff0000 Subnetmask 0xfffff000
        Net 0xac1a0000 Subnet 0xac1a0000
        Ethernet address is 00:06:6a:00:50:ba
        Metric is 0
        Maximum Transfer Unit size is 1500
        9081806 octets received
        1425622 octets sent
        153208 packets received
        18129 packets sent
        150530 broadcast packets received
        88 broadcast packets sent
        0 multicast packets received
        0 multicast packets sent
        0 input discards
        0 input unknown protocols
        0 input errors
        0 output errors

Summary of Contents for SilverStorm 9000



















































































































































































































Reviews:

No comments