manualshive.com logo in svg

Q CELLS Q.HOME+ESS HYB-G2, User Manual, Page: 24 / 64

Share
Download
Q CELLS Q.HOME+ESS HYB-G2 User Manual Download Page 24

17 

I

 

Operating Modes

 

 4.3 PV-Only Mode

          This mode enables the solar energy to be generated. However, the Battery charge-discharge
          does not operate. A maximum of 4.6kW or less of solar energy generation power can be sent
          to Grid based on the EMS decision. 

[ Figure 4-4 : Diagram of PV-Only Mode ]

 

 4.4 Battery-Discharge Mode

          This mode permits of no solar energy generation. Battery discharge is only available on this
          mode. Based on the EMS decision, the Battery discharge power can be sent maximum 3kW
          or less only to the Load.

[ Figure 4-5 : Diagram of Battery-Discharge Mode ]

Grid Output

Power

Load Output
Power(Main)

Load Output

Power(Sub)

PV Input

Power

Energy

Meter for

Utility

Battery

Power

One Way
Bi-directional way
Inactive

Grid Output

Power

Load Output
Power(Main)

Load Output

Power(Sub)

PV Input

Power

Energy

Meter for

Utility

Battery

Power

One Way
Bi-directional way
Inactive

Summary of Contents for Q.HOME+ESS HYB-G2

































































Reviews:

No comments