PVA TePla IoN 3 Technical Manual Download Page 14 | Manualshive

Page: 14 / 30

PVA TePla IoN 3 Technical Manual Download Page 14

Document No.: 1P0446-1 Rev. B, April 7, 2014

14

Section 4 -

Installation

This manual outlines the requirements for system installation, work area allowance, and initial startup

procedure. The installer should refer to

warnings and

instructions on the previous

pages

before beginning installation.

4.1

Facilities Requirements

The specifications and requirements for the system and applicable options are listed as follows:

System

:

x

Weight

: 75 lbs. Designed for use on table top or counter

x

Dimensions (door closed)

: 13.75" W x 13.5" H x 21.5" L (349.25 x 342.9 x 546.1mm)

Chamber

:

x

Dimensions (interior)

: 5 x 5 x 6" Deep (127 x 127 x 152.4 mm)

x

Material

: 6061-T6 high grade aerospace aluminum

Electrical

:

110-220VAC, 1 phase, 10 amp, 50-60 Hz, 18 AWG, 3 wire. The power cord is supplied by PVA

TePla America Inc.

Process Gases

:

x

Regulated to 10 PSIG before entering the system

x

Connections made by

.25” O.D.

corrosion resistant materials such as stainless steel or Teflon

tubing (supplied by purchaser). Other materials can generate particulate matter via corrosion

which will clog gas shutoff valves.

Gas Fittings

:

x

1/4" FPT fittings (the gas lines will need

¼” Swagel

ok ferrule style compression fittings--to

connect the incoming gas to the back of the IoN 3 MHz system)

Vacuum Pump

:

x

a KF25 flange is required to connect the vacuum hose to the IoN 3 MHz.

Internal RF Power Generator:

x

150 Watts +/-5%@ full load output into 50 Ohm impedance

x

13.5MHz operating frequency

x

Solid state circuitry

x

Automatic impedance matching

«
...
12
13
14
15
16
...
»

Summary of Contents for IoN 3































Reviews:

No comments