manualshive.com logo in svg

PVA TePla IoN 3, Technical Manual, Page: 13 / 30

Share
Download
PVA TePla IoN 3 Technical Manual Download Page 13

Document No.: 1P0446-1 Rev. B,  April 7, 2014 

 

 

 

13 

Section 3 -

 

Unpacking 

The IoN 3 MHz Plasma System is completely tested and inspected at the factory before shipping. 

Inspect the crate before unpacking. If there is any reason to suspect damage to the carton or its 

contents, make note of the damage, take pictures and report it to the shipping company. All pictures 

and information should be sent to PVA TePla America Inc. as well. All systems are shipped with tilt 

indicators. Your shipping department should inspect the crate and all tilt indicators prior to accepting 

the shipment.  
Using the included packing list, check to ensure that all listed components have arrived at your 

facility. Unpack the shipping cartons carefully and inspect the main plasma unit and all other system 

components for any damaged or missing items.  
If any component is damaged or missing, notify the shipper and notify the PVA TePla America Inc. 

Customer Service Department by TELEPHONE immediately. Claims based on late notification of 

shipping damage will be denied.  
Keep all shipping containers and materials in case it should be necessary to return any item to PVA 

TePla America Inc. All service and warranty work is done 

at  the  manufacturer’s  site

.  

Place the system components on the selected work surfaces. Remove all packing materials including 

any that might be present in the chamber of the system. Please view the video on the proper start-up 

of your IoN 3 MHz before starting your system.  
 

3.1

 

Long Term Storage  

If the plasma system and vacuum pump are to be placed in long term storage, take the following 

precautions in order to keep the equipment in good working condition. All system components should 

be placed in protective packaging. A desiccant

 

should be placed in the packaging to minimize 

moisture exposure. Storage should be in a room with humidity less than eighty percent.  
Before packaging and storing the vacuum pump, fill the pump reservoir with oil to the proper level 

and run the pump for five minutes to lubricate the seals. During the time the pump is stored, you will 

also need to run the pump for five minutes every three months in order to keep the seals lubricated.  
 

Summary of Contents for IoN 3































Reviews:

No comments