PureTools PT-PMS-42S User Manual Download Page 52

Page: 52 / 68

User Manual

PT-PMS-42S

Command

Description

Command Example and Feedback

[port]:45

[CEC]: blue ray stop.

#SEND_CECCMD
[port]:46

Pause.

#SEND_CECCMD 03:46

[CEC]: blue ray pause.

#SEND_CECCMD
[port]:48

Rewind

#SEND_CECCMD 03:48

[CEC]: blue ray backward.

#SEND_CECCMD
[port]:49

Fast forward.

#SEND_CECCMD 03:49

[CEC]: blue ray forward.

#SEND_CECCMD
[port]:4B

Forward.

#SEND_CECCMD 03:4B

[CEC]: blue ray skid forward.

#SEND_CECCMD
[port]:4C

Backward.

#SEND_CECCMD 03:4C

[CEC]: blue ray skid backward.

#SEND_CECCMD
[port]:6C

Power off.

#SEND_CECCMD 03:6C

[CEC]: Source Power off.

#SEND_CECCMD
[port]:6D

Power on.

#SEND_CECCMD 03:6D

[CEC]: Source Power on.



Control the output display:

Command

Description

Command Example and Feedback

#SEND_CECCMD
[port]:34

Input channel selection.

#SEND_CECCMD 04:34

[CEC]: TV input select

#SEND_CECCMD
[port]:41

Volume up.

#SEND_CECCMD 04:41

[CEC]: TV VOL +

#SEND_CECCMD
[port]:42

Volume down.

#SEND_CECCMD 04:42

[CEC]: TV VOL -

#SEND_CECCMD
[port]:43

Mute

#SEND_CECCMD 04:43

[CEC]: TV VOL Mute

#SEND_CECCMD
[port]:36

Power off.

#SEND_CECCMD 04:36

[CEC]: TV Power off

#SEND_CECCMD
[port]:04

Power on.

#SEND_CECCMD 04:04

[CEC]: TV Power on

Summary of Contents for PT-PMS-42S




































































Search results

Summary of Contents for PT-PMS-42S

Reviews:

Related manuals for PT-PMS-42S

Brands by name

Popular brands

PureTools PT-PMS-42S, User Manual

Search results

Summary of Contents for PT-PMS-42S

Reviews:

Related manuals for PT-PMS-42S

Brands by name

Popular brands