PureTools PT-PMS-42S User Manual Download Page 42

Page: 42 / 68

User Manual

PT-PMS-42S

8.2.1

System Control

Command

Description

Command Example and
Feedback

#SYS_SET_DEVICE_MOD
LE ****

Rename system model to ****.

#SYS_SET_DEVICE_MODLE
PT-PMS-42S

PT-PMS-42S

#SET_PWR_STATE ON

System on.

@PWR_STATE PWON

#SET_PWR_STATE OFF

System standby.

@PWR_STATE PWOFF

#GET_PWR_STATE

Get the system power status.

@PWR_STATE PWON

@PWR_STATE PWOFF

#SET_KEYPAD_LOCK ON

Lock front panel buttons.

@KEYPAD_LOCK ON

#SET_KEYPAD_LOCK
OFF

Unlock front panel buttons.

@KEYPAD_LOCK OFF

#GET_KEYPAD_LOCK

Get the front panel buttons locking
status.

@KEYPAD_LOCK ON

@KEYPAD_LOCK OFF

#GET_DEVICE_TYPE

Get system model.

PT-PMS-42S

#GET_DEVICE_IPADDR

Get GUI IP address.

@IP_ADDR: 192.168.0.178

#FACTORY_RESET

Reset to factory default.

FACTORY_RESET

#GET_DEVICE_FIRMWAR
EINF

Get firmware version.

FIRMWARE V1.0.0

#SET_PORT_RELAY 01
ON

Turn on PoC for HDBT output port. The
PT-HDBT-210-RX receiver can be
powered by the switcher.

@PORT_RELAY 01 ON

#SET_PORT_RELAY 01
OFF

Turn off PoC for HDBT output port.

@PORT_RELAY 01 OFF

#GET_PORT_RELAY 01

Get PoC status.

@PORT_RELAY 00
@PORT_RELAY 01

Summary of Contents for PT-PMS-42S




































































Search results

Summary of Contents for PT-PMS-42S

Reviews:

Related manuals for PT-PMS-42S

Brands by name

Popular brands

PureTools PT-PMS-42S, User Manual

Search results

Summary of Contents for PT-PMS-42S

Reviews:

Related manuals for PT-PMS-42S

Brands by name

Popular brands