Pulsar Blackbox Instruction Manual Download Page 10

Page: 10 / 76

Page

Product Specification

Physical

Wall Mount
Outside dimensions

130 x 130 x 60 mm

Weight

Nominal 0.65 kg

Enclosure material/description

ABS base with Polycarbonate lid,
flammability rating UL94HB

Cable entry detail

underside fitted with 3 x M20, nylon cable
glands suitable for 6 – 12mm cable

Transducer cable extensions

2-core screened

Maximum separation

1000 m

Environmental

IP Rating (Wall)

IP66/67

Max. & min. temperature (electronics)

-20 ºC to +50 ºC

Flammable atmosphere approval

Safe area: compatible with approved dB
transducers (see transducer spec' sheet)

CE approval

EMC approval to BS EN 50081-1:1992 for
emissions and BS EN50082-2:1995 for
immunity,

and to BS EN61010-1:1993 for low voltage
directive

Performance

Accuracy

0.25%

of the measured range or

6 mm (whichever is greater)

Resolution

0.1%

of the measured range or 2 mm

(whichever is greater)

Max. range

Dependant on transducer (maximum 40m
dB40)

Min. range

Dependent upon transducer (minimum zero
dB Mach 3)

Rate response

fully adjustable

Echo Processing

Description

DATEM (

igital

daptive

racking of

cho

ovement)

Outputs

Analogue output

0 to 5VDC into minimum load 10K

Ω

non-isolated (user programmable and
adjustable) 0.1%

resolution

Serial Port

RS232 for programming and data extraction

Volt free contacts, number and rating

2 form "C" (SPDT) rated at 2A at 240V AC

Programming

PC programming (standard)

via RS232 using supplied software

Remote programming (optional)

via RS232 using optional hand held
calibrator

Programming security

Via passcode (user selectable and
adjustable)

Programmed data integrity

Via non-volatile RAM

Summary of Contents for Blackbox













































































Search results

Summary of Contents for Blackbox

Reviews:

Related manuals for Blackbox

Brands by name

Popular brands

Pulsar Blackbox, Instruction Manual

Search results

Summary of Contents for Blackbox

Reviews:

Related manuals for Blackbox

Brands by name

Popular brands