Pulsar Blackbox Instruction Manual Download Page 26

Page: 26 / 76

Page

There are two main operating modes for your

blackbox

Run Mode

and

Program Mode

. There is also a

Test Mode

, used for checking the set-up.

All modes are now described.

Run Mode

This mode is used once the

blackbox

has been set up in program mode. It is

also the default mode that the unit reverts to when it resumes operation after
a power failure.

When the

blackbox

is switched on for the first time, it will provide an output

proportional to the distance from the transducer to the target, in metres. All
relays by default are switched off.

If either the PC Programming Software (standard) or the Hand Held
Calibrator (optional), are connected to the

blackbox

, via the RS232

interface, whilst the

blackbox

is in the RUN mode then the current

measurement will be displayed, dependent on mode and measurement unit's
chosen.

After programming is complete, any relays that are set will operate when the
measurement reaches the relevant setpoint.

Summary of Contents for Blackbox













































































Search results

Summary of Contents for Blackbox

Reviews:

Related manuals for Blackbox

Brands by name

Popular brands

Pulsar Blackbox, Instruction Manual

Search results

Summary of Contents for Blackbox

Reviews:

Related manuals for Blackbox

Brands by name

Popular brands