Pulsar Blackbox Instruction Manual Download Page 20

Page: 20 / 76

Page

Preparat

Preparation for Operation

ion for Operation

Before switching on, check the following:

The

blackbox

is mounted correctly and is in a ‘safe’ area.

The power supply is correctly installed.

The voltage selector switch is in the correct position.

The relays are connected correctly.

Main

Maintenance

tenance

There are no user serviceable parts inside your

blackbox

, except the mains

power fuse. If you experience any problems with the unit, then please
contact Pulsar Process Measurement for advice.

To clean the equipment, wipe with a damp cloth. Do not use any solvents on
the enclosure.

Important Information

The unique DATEM software comes into operation as soon as power is
applied, and is designed to monitor a

moving level

target

with the

transducer

in a

fixed position.

If, after any period of use, it should become necessary to move the
transducer, for any reason, from its original operating position, switch off
the

blackbox

, before proceeding, to prevent any undesirable updates to the

DATEM trace. If after moving the transducer the reading is not as expected
please refer to

Chapter 6 Troubleshooting

Summary of Contents for Blackbox













































































Search results

Summary of Contents for Blackbox

Reviews:

Related manuals for Blackbox

Brands by name

Popular brands

Pulsar Blackbox, Instruction Manual

Search results

Summary of Contents for Blackbox

Reviews:

Related manuals for Blackbox

Brands by name

Popular brands