Pulsar Blackbox Instruction Manual Download Page 42

Page: 42 / 76

Page

Parameter Listing

This section describes all of the parameters. Any parameter can be reset to

its default, by pressing the

hot key, whilst in program mode.

Application Parameters

Operation

P100 Mode of Operation

This parameter sets the mode of operation, when in run mode, and can be set
to one of the following:

Option

Description

1 = Distance
(Default)

Display and Output relative to the

distance

from the

transducer to the surface.

2 = Level

Display and Output relative to how

full

the vessel is.

3 = Space

Display and Output relative to how

empty

a vessel is.

P101 Transducer

This parameter should be set to the transducer being used with the unit, and
can be set to one of the following:

Option

Description

1 = dB3

Transducer is a dB3.

2 = dB6 (Default)

Transducer is a dB6.

3= dB10

Transducer is a dB10.

4= dB15

Transducer is a dB15.

5= dB25

Transducer is a dB25.

6 = dB40

Transducer is a dB40.

7 = dBS6

Transducer is a dBS6

Summary of Contents for Blackbox













































































Search results

Summary of Contents for Blackbox

Reviews:

Related manuals for Blackbox

Brands by name

Popular brands

Pulsar Blackbox, Instruction Manual

Search results

Summary of Contents for Blackbox

Reviews:

Related manuals for Blackbox

Brands by name

Popular brands