background image

sensALIGN rechargeable battery

Both sensALIGN laser and sensALIGN sensor are powered using the sensALIGN rechargeable bat-
tery. The battery is charged via the charger/adapter socket using the sensALIGN charger/adapter. If
the battery capacity is greater than 50% [acceptable capacity for measurement], the battery status LED
on both sensALIGN laser and sensor lights up green for 2 seconds on switching on. During the char-
ging process, the battery status LED blinks green. When the battery is fully charged, the LED lights
steady green if the charger remains connected.

Activity

sensALIGN laser battery
status LED

sensALIGN sensor battery
status LED

sensALIGN laser beam
active LED

Switch on

Lights up green for 3
seconds when battery run
time is > 10 hrs

Lights up green for 3
seconds when battery run
time is > 10 hrs

Lights steady red when in

beam finder mode

Blinks red when in meas-
urement mode

Note that measuring can
take place with both
modes

Blinks green every 3
seconds when battery run
time is between 5 – 10 hrs

Blinks green every 3 seconds
when battery run time is
between 1 – 5 hrs

Blinks red every 3 seconds

when battery run time is

between 1 – 5 hrs

Blinks red every 3 seconds
when battery run time is
insufficient for longer meas-
urements

Blinks red constantly when

battery run time is < 1 hr

Blinks red constantly when
battery run time is < 1 hr

8

Edition: (Undefined variable: General.Edition)

(Undefined variable: General.UserGuideTitle)

Summary of Contents for Rotalign Touch































Reviews: