ProSoft Technology PLX51-HART-4I User Manual Download Page 58

Page: 58 / 127

PLX51-HART-4I / PLX51-HART-4O

♦

HART Input/Output

Operation

Multidrop Field Devices

User Manual

ProSoft Technology, Inc.

Page 58 of 127

MultiDrop UDT Structure

Figure 4.7 – Multidrop – UDT

Table 4.8 – Multidrop UDT structure

Parameter

Datatype

Description

PollStatus

SINT

Bit 0 – When set this bit will indicate that the device is

online

LastStatusByte

SINT

The first byte of the field device HART response

status. See the HART section at the end of this

document for details regarding the HART status.

LastSecond_StatusByte

SINT

The second byte of the field device HART response

status. See the HART section at the end of this

document for details regarding the HART status.

ManufactureIDCode

SINT

The unique manufacturer identification code.

DeviceTypeCode

SINT

The device type code specified by the

manufacturer.

MinPreambles

SINT

Minimum Number of Preambles.

UniversalCMDMajor

SINT

Universal Command Major Revision Number.

Summary of Contents for PLX51-HART-4I
































































































































Search results

Summary of Contents for PLX51-HART-4I

Reviews:

ProSoft Technology PLX51-HART-4I, User Manual, Page: 58 / 127

Search results

Summary of Contents for PLX51-HART-4I

Reviews: