manualshive.com logo in svg

ProSoft Technology PLX51-HART-4I, User Manual, Page: 18 / 127

Share
Download
ProSoft Technology PLX51-HART-4I User Manual Download Page 18

PLX51-HART-4I / PLX51-HART-4O 

♦

 HART Input/Output 

Installation 

Multidrop Field Devices  

User Manual 

ProSoft Technology, Inc. 

Page 18 of 127 

As indicated in the diagrams below, the PLX51-HART-4I can support multidrop 

devices in parallel with either module-powered or externally-powered configurations. 

 

Figure 2.17  – PLX51-HART-4I - Multidrop Wiring – Parallel – Module Powered 

 

Figure 2.18  – PLX51-HART-4I - Multidrop Wiring – Parallel – Externally Powered 

 

Figure 2.19  – PLX51-HART-4O - Multidrop Wiring – Parallel 

Note: 

It is not recommended to multidrop 4-wire devices unless all devices make use of isolated power 

supplies. 

2.6  Ethernet Port 

The Ethernet connector should be wired according to industry standards. Refer to the 

additional information section in this document for further details. 

Summary of Contents for PLX51-HART-4I
































































































































Reviews:

No comments