manualshive.com logo in svg

ProSoft Technology PLX51-HART-4I, User Manual, Page: 57 / 127

Share
Download
ProSoft Technology PLX51-HART-4I User Manual Download Page 57

PLX51-HART-4I / PLX51-HART-4O 

♦

 HART Input/Output 

Operation 

Multidrop Field Devices  

User Manual 

ProSoft Technology, Inc. 

Page 57 of 127 

4.1.4  Multidrop 

When using Multidrop HART devices with Logix, the user must select the Logix Tag 

to be used to populate the HART device data. The user can either select to use the 

current Multidrop tag structure or the legacy MVI56Legacy tag structure.  
The user will need to use either of the provided MultiDrop UDTs for each tag used for 

each HART multidrop device (as shown below): 

 

Figure 4.6 – Multidrop – new and legacy UDTs 

Important

: If the user does not use the provided UDTs it can result in unexpected behavior or no data 

updates. 

Once the Logix tags for each multidrop HART device have been selected, the 

PLX51-HART-4x will automatically update the Logix tags with the data from each 

multidrop HART device on each HART channel.  

Summary of Contents for PLX51-HART-4I
































































































































Reviews:

No comments