manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, User Manual

Share
Download
ProSoft Technology inRAx MVI56-CAS User Manual Download Page 9

Start Here 

MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 9 of 86 

December 26, 2007 
 

1 Start 

Here 

In This Chapter 

¾

 System 

Requirements.............................................................. 9 

¾

 Package 

Contents.................................................................. 10 

¾

 Setting 

Jumpers ..................................................................... 11 

¾

  Install the Module in the Rack ................................................ 12 

¾

  Connect your PC to the Processor......................................... 13 

¾

  Download the Sample Program to the Processor .................. 14 

¾

  Connect your PC to the Module ............................................. 17 

Installing the MVI56-CAS module requires a reasonable working knowledge of 
the Rockwell Automation hardware, the MVI56-CAS Module and the application 
in which they will be used. 

Caution: 

It is important that those responsible for implementation can complete 

the application without exposing personnel, or equipment, to unsafe or inappropriate 
working conditions. Safety, quality and experience are key factors in a successful 
installation. 

 

1.1 System 

Requirements 

The MVI56-CAS module requires the following minimum hardware and software 
components: 

ƒ

  Rockwell Automation ControlLogix™ processor, with compatible power 

supply and one free slot in the rack, for the MVI56-CAS module. The module 
requires 800mA of available power.  

ƒ

  Rockwell Automation RSLogix 5000 programming software version 2.51 or 

higher. 

ƒ

  Rockwell Automation RSLinx communication software 

ƒ

  Pentium® II 450 MHz minimum. Pentium III 733 MHz (or better) 

recommended  

ƒ

  Supported operating systems: 

o

  Microsoft Windows XP Professional with Service Pack 1 or 2  

o

  Microsoft Windows 2000 Professional with Service Pack 1, 2, or 3 

o

  Microsoft Windows Server 2003  

ƒ

  128 Mbytes of RAM minimum, 256 Mbytes of RAM recommended  

Summary of Contents for inRAx MVI56-CAS























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands