manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, User Manual

Share
Download
ProSoft Technology inRAx MVI56-CAS User Manual Download Page 13

Start Here 

MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 13 of 86 

December 26, 2007 
 

3 

With a firm but steady push, snap the module into place.  

4 

Check that the holding clips on the top and bottom of the module are securely 
in the locking holes of the rack. 

5 

Make a note of the slot location. You will need to identify the slot in which the 
module is installed in order for the sample program to work correctly. Slot 
numbers are identified on the green circuit board (backplane) of the 
ControlLogix rack.  

6 

Turn power ON. 

Note: 

If you insert the module improperly, the system may stop working, or may 

behave unpredictably.  

Note: 

If you are installing MVI56-CAS with other modules connected to the PCI bus, 

the peripheral modules will not have holding clips. Make sure all of the modules are 
aligned with their respective slots before you snap them into place. 

 

1.5 

Connect your PC to the Processor 

7 

Connect the right-angle connector end of the cable to your controller at the 
communications port. 

 

Summary of Contents for inRAx MVI56-CAS























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands