manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, User Manual

Share
Download
ProSoft Technology inRAx MVI56-CAS User Manual Download Page 14

MVI56-CAS 

♦

 ControlLogix Platform 

Start Here 

Teledyne CA Slave Module  

 

Page 14 of 86  

ProSoft Technology, Inc. 

December 26, 2007 

 

8 

Connect the straight connector end of the cable to the serial port on your 
computer.  

 

 

1.6 

Download the Sample Program to the Processor 

¾

 

To download the sample program from RSLogix 5000 to the 
ControlLogix processor: 

Note: 

The key switch on the front of the ControlLogix module must be in the REM 

position. 

1 

If you are not already online to the processor, open the Communications 
menu, and then choose Download. RSLogix will establish communication 
with the processor. 

2 

When communication is established, RSLogix will open a confirmation dialog 
box. Click the Download button to transfer the sample program to the 
processor.  

 

3 

RSLogix will compile the program and transfer it to the processor. This 
process may take a few minutes.  

Summary of Contents for inRAx MVI56-CAS























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands