manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, User Manual

Share
Download
ProSoft Technology inRAx MVI56-CAS User Manual Download Page 37

Diagnostics and Troubleshooting 

MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 37 of 86 

December 26, 2007 
 

4.1.6 Data 

Analyzer 

The data analyzer mode allows you to view all bytes of data transferred on each 
port. Both the transmitted and received data bytes are displayed. Use of this 
feature is limited without a thorough understanding of the protocol. 

Note:

 The Port selection commands on the Data Analyzer menu differs very slightly in 

different modules, but the functionality is basically the same. Use the illustration above 
as a general guide only. Refer to the actual data analyzer menu on your module for the 
specific port commands to use.

 

Important: 

When in analyzer mode, program execution will slow down. Only use this 

tool during a troubleshooting session. Before disconnecting from the Config/Debug 
port, please press 

[S]

 to stop the data analyzer, and then press 

[M]

 to return to the 

main menu. This action will allow the module to resume its normal high speed 
operating mode.  

Analyzing Data for the first application port 

Press 

[1]

 to display I/O data for the first application port in the Data Analyzer. 

The following illustration shows an example of the Data Analyzer output. 

 

 

Analyzing Data for the second application port 

Press 

[2]

 to display I/O data for the second application port in the Data Analyzer. 

Displaying Timing Marks in the Data Analyzer 

You can display timing marks for a variety of intervals in the data analyzer 
screen. These timing marks can help you determine communication-timing 
characteristics. 

Key Interval 

[5] 1 

milliseconds 

ticks 

[6] 5 

milliseconds 

ticks 

[7] 

10 milliseconds ticks 

[8] 

50 milliseconds ticks 

[9] 

100 milliseconds ticks 

[0] 

Turn off timing marks 

 

 

Removing Timing Marks in the Data Analyzer 

Press 

[0]

 to turn off timing marks in the Data Analyzer screen. 

Summary of Contents for inRAx MVI56-CAS























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands