manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, User Manual

Share
Download
ProSoft Technology inRAx MVI56-CAS User Manual Download Page 69

Reference MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 69 of 86 

December 26, 2007 
 

Group Register Content Description 

 6022 

Port 2 
Errors 
Received 

This field contains the total number of message errors 
received on the port. 

 6023 

Read Block 
Count 

This field contains the total number of read blocks 
transferred from the module to the processor. 

 6024 

Write Block 
Count 

This field contains the total number of write blocks 
transferred from the processor to the module. 

 6025 

Parse Block 
Count 

This field contains the total number of blocks 
successfully parsed that were received from the 
processor. 

 6026 

Command 
Event Block 
Count 

This field contains the total number of command event 
blocks received from the processor. 

 6027 

Command 
Block Count 

This field contains the total number of command 
blocks received from the processor. 

 6028 

Error Block 
Count 

This field contains the total number of block errors 
recognized by the module. 

 6029 

Port 1 
Current 
Error/Index 

For a slave port, this field contains the value of the 
current error code returned. For a master port, this 
field contains the index of the currently executing 
command. 

 6030 

Port 1 Last 
Error 

For a slave port, this field contains the value of the 
last error code returned. For a master port, this field 
contains the index of the command with an error. 

 6031 

Port 2 
Current 
Error 

For a slave port, this field contains the value of the 
current error code returned. For a master port, this 
field contains the index of the currently executing 
command. 

 6032 

Port 2 Last 
Error 

For a slave port, this field contains the value of the 
last error code returned. For a master port, this field 
contains the index of the command with an error. 

 6033 

Port 1 
Status Scan 

This register contains the port's Scan Status in the 
upper byte and the port's current Error Status in the 
lower byte. The Scan Status is encoded in the upper 
byte as follows: 
Bit 13 - Status Data scan 
Bit 14 - Analog Data scan 
Bit 15 - Read All Data scan 

 6034 

Port 2 
Status Scan 

This register contains the port's Scan Status in the 
upper byte and the port's current Error Status in the 
lower byte. The Scan Status is encoded in the upper 
byte as follows: 
Bit 13 - Status Data scan 
Bit 14 - Analog Data scan 
Bit 15 - Read All Data scan 

 6703 

Spare 

Spare 

 

 -  

 -  

- 

 6799 

Spare 

Spare 

 

 

Summary of Contents for inRAx MVI56-CAS























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands