manualshive.com logo in svg

PRONAR T386, Operator'S Manual, Page: 85 / 162

Share
Download
PRONAR T386 Operator'S Manual Download Page 85

SECTION 4 

Pronar T386 

4.17 

  Make sure that the hitching operation was completed and the second 

trailer drawbar is secured. 

  Connect conduits of pneumatic, hydraulic and electrical systems according to 

instructions contained in section (4.3) 

Unhitching the second trailer 

  Immobilise tractor and trailers with parking brake. 

  Turn off tractor engine. Ensure that unauthorised persons do not have access 

to the tractor cab. 

  Disconnect conduits of pneumatic, hydraulic and electrical systems according 

to instructions contained in section 4.3. 

  Unlock  the  pin  of  the  rear  hitch  of  the  first  trailer.  Remove  drawbar  pin  and 

drive tractor away. 

 

DANGER 

 

When hitching/unhitching the trailer, there must be nobody between the trailers. Person 
assisting hitching up machines should stand outside the area of danger and be visible to 
the tractor driver at all times. 

 

WARNING 

 

Do NOT hitch a second trailer constructed on any chassis except dual axle chassis. 

 

Summary of Contents for T386



































































































































































Reviews:

No comments